تصفح كتالوجنا الشامل من المنتجات الصناعية الممتازة من علامات تجارية عالمية مرموقة.
لم يتم العثور على نتائج
عرض 108 من 108 منتجًا
NTN-SNR deep groove ball bearings are the workhorse bearing for general industrial rotating equipment — motors, pumps, fans, and conveyors. Engineered for low friction and high-speed operation, they handle radial loads with light axial load...
Load type: Primarily radial, moderate axial (bidirectional)
عرض التفاصيلNTN-SNR angular contact ball bearings combine radial load capacity with one-directional thrust support, and are typically mounted in pairs for bidirectional axial loading. Their high-speed capability suits pump and compressor drive ends and...
Load type: Combined radial + unidirectional axial (pair for bidirectional)
عرض التفاصيلSelf-aligning ball bearings automatically accommodate shaft deflection and housing misalignment while running at high speed with low friction — a lighter-duty complement to spherical roller bearings for fans, conveyors, and general industri...
Load type: Radial, with limited axial capacity
عرض التفاصيلBuilt for the heaviest, most demanding rotating equipment, NTN-SNR spherical roller bearings combine high radial and axial load capacity with a self-aligning design that tolerates shaft deflection and housing misalignment. Ideal for crusher...
Load type: Heavy radial + moderate axial (bidirectional)
عرض التفاصيلNTN-SNR tapered roller bearings carry combined radial and thrust loads on gearboxes, pump drives, and heavy rotating machinery. Their conical roller geometry allows precise clearance adjustment at installation, delivering the strength and r...
Load type: Heavy radial and axial (paired for bidirectional thrust)
عرض التفاصيلDesigned for heavy radial loads at high speed, NTN-SNR cylindrical roller bearings are a common choice for electric motors, compressors, and gearboxes across oil & gas and general industry. Certain designs permit axial displacement, making ...
Load type: Heavy radial only (little to no axial capacity)
عرض التفاصيلPre-assembled, self-aligning bearing units let maintenance teams bolt a ready-to-run bearing straight onto equipment frames — no housing design or precision fitting required. Available as pillow blocks, flanged units, cartridges, or hangers...
Shaft diameter range: Roughly 12 mm – 140 mm
عرض التفاصيلSplit and solid plummer-block housings support large-diameter shafts on heavy, continuous-duty rotating equipment such as pumps, fans, and crushers. The standard SNC range covers 20–160 mm shafts, while the ductile-iron SNCD series extends ...
Shaft diameter: SNC 20–160 mm; SNCD 75–500 mm (ductile iron)
عرض التفاصيلA dedicated range of mounting and dismounting tools — sleeve kits, locknut spanners, assembly paste, induction heaters, and pullers — engineered to install and remove NTN-SNR bearings without damage. Essential companion products for any mai...
Mounting: Sleeve kits, hook/pin spanners (KM/KML/KMK nuts, B/TB/BR/TBR locknuts)
عرض التفاصيلThe LUB'SOLUTION range covers greases and lubrication accessories matched to bearing type and duty condition, protecting rolling equipment and extending service life. A recurring consumable for any maintenance program, it pairs naturally wi...
Product form: Greases and lubrication accessories/dispensing aids
عرض التفاصيلSteel-bodied, bolted pig that runs in either flow direction for hydrostatic testing, water/air displacement, debris removal, and product separation. Available 4"–56" with guiding and sealing discs as standard; enhance cleaning with brushes,...
Size range: 4" – 56"
عرض التفاصيلSteel-bodied pig using piston-style scraper cups that aggressively scrape the pipe bore while holding a constant seal. Sized 4"–56" with four cups as standard for light-to-medium debris removal, batching, and gauging; upgrade with brushes, ...
Size range: 4" – 56"
عرض التفاصيلSteel-bodied pig with flexible conical cups that maintain a constant seal through pipe ovality, wall-thickness variation, and diameter reductions of up to 20%. A long-standing choice for offshore lines. Sized 4"–56" with 2–4 cups as standar...
Size range: 4" – 56"
عرض التفاصيلSteel-bodied pig combining two functional modules — e.g., cleaning plus gauging or batching — in a single run to cut cost and downtime. Configurable with cups and/or discs, sized 6"–56", and rated for short-radius bends and tees. Add brushe...
Size range: 6" – 56"
عرض التفاصيلSteel-bodied pig built specifically for dewatering, using sandwich packages of elastomeric sealing discs and high-density foam discs for high-performance sealing. Sized 4"–56" (single or multi-bolt body) for water/air displacement after hyd...
Size range: 4" – 56"
عرض التفاصيلLightweight cup or disc pig with a single flexible polyurethane body on a metal or plastic holder — easy to handle and popular where a full steel body isn't needed. Sized 4"–24" for light-to-medium debris removal, batching, and gauging; add...
Size range: 4" – 24"
عرض التفاصيلOne-piece, compressible polyurethane foam pig available in 50+ styles from 1"–100", in low, medium, or high foam density. Ideal for lines with bore restrictions, ID changes, or tight bends — or pipelines that have never been pigged. Manufac...
Size range: 1" – 100"
عرض التفاصيلStudded polyurethane pig with tungsten-steel pins, built using soft-core process technology to mechanically break up and remove coke deposits from refinery heaters and pipes. Sized 1.000"–12.500"; solid (unstudded) decoking pigs also availa...
Size range: 1.000" – 12.500"
عرض التفاصيلSolid or inflatable polyurethane sphere that maintains continuous pipe-wall contact for reliable batching, product separation, meter proving, and pipeline evacuation. Inflatable units are filled with a water/glycol mix; FDA food-grade mater...
Design: Solid or inflatable
عرض التفاصيلComprehensive range of replacement parts for in-house and third-party pigs, including sealing and guiding discs, circular and spring-mounted brushes, polyurethane plough blades, magnet boxes, and aluminum gauge plates or cups (conical or st...
Parts range: Discs, brushes, plough blades, magnets
عرض التفاصيلCompact, stainless-steel pig transmitter for tracking steel-bodied or foam pigs during a run. Delivers 500+ hours of operating time on standard batteries and up to 23 metres of signal range, mounts via bolt-on flange, and can be switched on...
Operating time: 500+ hours
عرض التفاصيلIntrusive, omni-directional signaller that mounts on the pipeline to confirm pig passage — whether leaving the launcher, arriving at the receiver, or passing a marked intermediate point. The omni-directional trigger removes the fitting-orie...
Trigger design: Omni-directional
عرض التفاصيلDouble-isolation plug with two independent inflatable tyres and a monitored test cavity between them, letting operators prove positive isolation before hot work on hydrocarbon pipelines — a safer alternative to air bags or compression plugs...
Isolation: 2 independent inflatable tyres
عرض التفاصيلMechanically or hydraulically actuated test plug that grips the internal pipe bore and seals with a polyurethane element — no welded end caps or flanges required. Used singly or in pairs (one fills, one vents) to hydrostatically pressure-te...
Actuation: Mechanical or hydraulic
عرض التفاصيلLocalized weld-test system — available as a Flange Weld Test Plug or Internal Joint Test Plug — that pressure-tests a single new weld without flooding and dewatering the whole pipeline. Covers ½"–24" as standard (larger on request) at test ...
Tool styles: Flange Weld & Internal Joint Test Plug
عرض التفاصيلPolyEurope's certified rental fleet of pigs and isolation/testing tools for short-term or one-off jobs. The flagship hire item, the Bi-Directional Hire Pig (steel body, 6"–36", multi-bolt), comes pre-fitted with a transmitter cavity for tra...
Bi-Di hire pig size: 6" – 36"
عرض التفاصيلA pneumatic knockout hammer built to drive Elliott's hardened knockout bits, the Jumbo Tube Buster punches cut tube stubs free from tube sheets in heat exchangers, firetube, and watertube boilers. Its compact, lightweight barrel design gets...
Tube size: 0.625" – 2.000" OD (15.9–50.8mm)
عرض التفاصيلElliott's Stub Tugger is a hydraulic ram-style puller that delivers up to 30 tons of pulling force through a 6" stroke to extract stubborn tube stubs from heat exchangers and boilers. Its brute hydraulic force handles stubs that resist knoc...
Tube size: 0.375" – 3.000" OD (9.5–76.2mm)
عرض التفاصيلThe Tube Tugger is a semi-continuous hydraulic pulling system that breaks the tube-sheet joint bond and extracts tubes from heat exchangers, chillers, and heat transfer vessels in a single high-production pass. Portable ram and pump compone...
Tube size: 0.625" – 1.250" OD (15.9–31.8mm)
عرض التفاصيلElliott's PTTC Push Type Tube Cutter scores or severs tubes from the inside right at the tube sheet face, using an adjustable collar to control cut depth and specially coated blades for extended life. It preps heat exchanger and boiler tube...
Tube size: 0.375" – 2.500" OD (9.5–63.5mm)
عرض التفاصيلThe Super Collet Tube Puller combines the gripping power of a spear with the speed of a collet, clamping onto a tube stub and pulling it free in seconds without damaging the tube sheet hole or requiring ID machining. Pulling capacity up to ...
Tube size: 0.50" – 2.50" OD (12.7–63.5mm)
عرض التفاصيلElliott's One-Revolution Series cutters vent and score tubes in a single pass, using more advanced blade and cutter engineering than older one-rev designs to last longer, resist wear, and cut with less applied force. Tube size range: 0.375"...
Tube size: 0.375" – 2.500" OD (9.53–63.5mm)
عرض التفاصيلThe 300 Series Boiler Tube Cutter is a power-driven, wheel-style ID cutter that trims firetube and watertube boiler tubes to length before roll beading. Built for the larger tube diameters typical of boiler applications, covering 2.000" – 3...
Tube size: 2.000" – 3.000" OD (50.8–76.2mm)
عرض التفاصيلElliott's SpeedCut pairs a rugged Baldor motor with Automatic Cutting Force Control to slice through an entire tube bundle and shell in one pass, handling copper, stainless, and exotic alloys. It replaces slow tube-by-tube cutting on large ...
Bundle diameter: Up to 98.5" (2.5m)
عرض التفاصيلThe Cyclgrip Semi-Continuous Tube Puller pulls tubes free of baffle and support-plate expansion at up to 10 ft per minute, replacing tiresome slam-hammer work. Its slim profile mounts to the side near water boxes and channel plates for acce...
Tube size: 0.500" – 1.000" OD (12.7–25.4mm)
عرض التفاصيلThe 24 Series Condenser Expander performs the straight-roll expansion that seats a new tube permanently into the tube sheet, sized for chillers, heat exchangers, feedwater heaters, fin-fan coolers, and surface condensers. Tube size range: 0...
Tube size: 0.500" – 2.000" OD (12.7–50.8mm)
عرض التفاصيلBuilt specifically for superheater and evaporator tubes in watertube boilers, the self-feeding 900 Series flares each tube end as it expands it — the joint geometry those applications require instead of a plain straight roll. Tube size rang...
Tube size: 0.620" – 1.500" OD (15.4–38.1mm)
عرض التفاصيلThe 4480 Series Single Roll Beading Expander performs combo rolling — expanding the tube into the sheet and forming the required end bead in one operation — matching the joint standard used in firetube boilers. Tube size range: 2.000" – 3.0...
Tube size: 2.000" – 3.000" OD (50.8–76.2mm)
عرض التفاصيلRecommended for re-rolling leaky tube joints in firetube boilers, the 40 Series Straight Boiler Expander restores a tight tube-to-sheet seal without pulling and replacing the tube. Tube size range: 2.000" – 3.000" OD.
Tube size: 2.000" – 3.000" OD (50.8–76.2mm)
عرض التفاصيلEngineered for the thick steam- and mud-drum tube sheets found in high-pressure boilers, the DRE Series Deep Roll Expander performs the deep, hard rolling those joints require, covering a 1.750" – 4.000" OD range.
Tube size: 1.750" – 4.000" OD (44.5–101.6mm)
عرض التفاصيلThe PX24 Series delivers true parallel-pin expansion — even radial force along the tube instead of a tapered roll — cutting the stress placed on welded tube joints versus conventional rolling. Built for use in assisted rolling systems, cove...
Tube size: 0.750" – 1.000" OD (19.05–25.4mm)
عرض التفاصيلThe 445 Series turns its drive head 90 degrees off-axis so it can roll boiler tubes in tight, hard-to-reach locations a straight motor can't access. Available in torque-controlled and stall-type versions with roll or lever throttle, it runs...
Tube size: 2.000" – 4.000" OD (50.8–101.6mm)
عرض التفاصيلThe ET850 is Elliott's next-generation push-pull rolling motor, using pneumatic torque control to stop expansion at a precise, repeatable target and guard against over-rolling in boiler and heat exchanger tubes. Tube size range: 0.750" – 1....
Tube size: 0.750" – 1.250" OD (19.1–31.8mm)
عرض التفاصيلScaled down for the small-bore tubes common in oil coolers and compact heat exchangers, the ET720 brings the same pneumatic torque control as its larger ET850 sibling to a 0.250" – 0.375" OD range, protecting delicate tubes from over-expans...
Tube size: 0.250" – 0.375" OD (6.35–9.525mm)
عرض التفاصيلFor extreme rolling applications, Elliott's Stall Torque Pneumatic Rolling Motors deliver more raw power than any other motor in the line, spanning an unusually wide 0.750" – 6.000" OD range for the toughest boiler tube jobs.
Tube size: 0.750" – 6.000" OD (19.1–152.4mm)
عرض التفاصيلThe 99 Series swaps compressed air for electric drive (110V or 220V), giving crews more consistent speed and torque than pneumatic motors — with comparable rolling power — across a broad 0.250" – 3.000" OD range for boiler and heat exchange...
Tube size: 0.250" – 3.000" OD (6.4–76.2mm)
عرض التفاصيلElliott's assisted rolling family — Table Hawk, Rapid Hawk (electric and hybrid), and Monster Hawk — takes the physical strain out of high-volume tube rolling. Table Hawk handles small tubes at the bench; Rapid Hawk's articulated arm cuts o...
Combined tube size: 0.25" – 3.00" OD (6.35–76.2mm)
عرض التفاصيلTorq N' Seal plugs expand into the tube with nothing more than a hand torque wrench, using an internal ferrule and drive screw to form a wide, gradual seal rated above 6,500 PSI without shocking the tube sheet. Built to ASME Section VIII/II...
Tube ID: 0.410" – 1.000" (10.4–25.4mm)
عرض التفاصيلElliott's Two-Piece Tube Plugs pair a tapered pin with a separate ring to spread the sealing contact over a larger area than a one-piece plug, reducing stress on the tube and tube sheet in low-pressure service up to 150 PSI. Tube size range...
Tube size: 0.375" – 1.250" OD (9.5–31.8mm)
عرض التفاصيلA simple tapered-pin plug covering the widest OD range in Elliott's plug lineup, the One-Piece Tube Plug seals leaking tubes fast in low-pressure heat exchangers and boilers up to 150 PSI. Tube size range: 0.375" – 3.000" OD.
Tube size: 0.375" – 3.000" OD (9.5–76.2mm)
عرض التفاصيلThe RECON 1250 and 2500 pressurize a tube through seals at each end and read the gauge for pressure drop, giving a fast go/no-go leak check across a 0.500" – 2.500" OD range — just connect air, seal both ends, and pressurize.
Tube size: 0.500" – 2.500" OD (12.7–63.5mm)
عرض التفاصيلThe RECON 1500 uses a Venturi system to pull vacuum on an isolated tube, flagging leaks by watching the gauge for vacuum loss. Trigger-operated with a T-handle plugging tool, it's a fast one-person alternative to pressure testing. Tube ID r...
Tube size (ID): 0.280" – 2.456" (7.1–62.4mm)
عرض التفاصيلThe Soot Buster is a pneumatically pulsed tool that propels itself down a firetube boiler tube, scrubbing soot and light-to-medium soft deposits from the ID with every pulse — no external push rod needed. Tube size range: 1.25" – 4" OD.
Tube size: 1.25" – 4" OD (31.8–101.6mm)
عرض التفاصيلThe 5224XL and 5125 Series use a rigid, high-torque shaft to clear light-to-medium soft deposits from straight heat exchanger tubes in a dry-flush process, built for industrial plants that need consistent mechanical cleaning power. Tube siz...
Tube size: 1.25" – 4" OD (31.8–101.6mm)
عرض التفاصيلElliott's Die-Hard was the first cableless tube cleaner: water pressure — not a spinning cable — drives its quad-brush, pulse-jet cleaning action at roughly 3 ft/second, scrubbing light-to-medium deposits from chiller, condenser, and heat e...
Tube size: 3/4" – 1" OD (19.1–25.4mm)
عرض التفاصيلA two-part prep set for retubing: Tube Sheet Hole Brushes clear hard deposits from tube sheet and support-plate holes, then Tube Pilots — a tapered nose with a replaceable nylon brush — center and guide each new tube through the cleaned hol...
Tube size: 0.500" – 1.500" OD (12.7–38.1mm)
عرض التفاصيلLarge fiberglass-reinforced axial flow fan installed beneath an air-cooled condenser cell, viewed from ground level looking up through the round FRP fan stack. Used to draw ambient air across finned-tube bundles condensing steam-turbine exh...
Blades: 8
عرض التفاصيلMotor-and-gearbox-driven axial fan fitted with a diamond-mesh safety guard, mounted beneath a finned-tube bundle bank. Typical of air-cooled heat exchangers used for process fluid, lube oil, and jacket-water cooling in refineries and petroc...
Drive: Motor-and-gearbox driven
عرض التفاصيلRow of large-diameter air-cooled condenser cells at an operating power plant, each housing an FRP axial fan beneath a raised maintenance platform. Illustrates full-scale ACC deployment: multiple fan cells arranged in banks to condense turbi...
Cells shown: 3
عرض التفاصيلFront-on view of a twin-fan air-cooled heat exchanger cell, showing two 7-blade FRP fans with adjustable-pitch hubs sharing a drive motor. Illustrates the compact fan/motor arrangement used on skid-mounted process coolers and package air-co...
Blades: 7 (per fan)
عرض التفاصيلAerial site photo of a large multi-blade FRP fan (~10 blades) laid flat during on-site assembly, with an installation crew fitting blades to the central hub ahead of hoisting into the fan stack. Documents the field erection process for larg...
Blades: ~10
عرض التفاصيلAerial construction-site photo of a large blue multi-blade FRP fan being assembled on the ground ahead of installation, tied to a documented project reference in Thailand. Illustrates the scale of Encon's export capability for large air-coo...
Blades: ~12-14
عرض التفاصيلMesh-guarded axial fan mounted on a skid radiator/heat-exchanger package, typical of engine-driven generator sets, compressor packages, or small process coolers. The fan pulls ambient air through the radiator core to reject heat from circul...
Guard: Mesh-guarded
عرض التفاصيلComplete field-erected counterflow cooling tower cell with corrugated FRP casing panels, access ladder, and top-mounted fan stack. Water falls vertically through fill media while air is drawn upward against the flow, rejecting process heat ...
Configuration: Single-cell
عرض التفاصيلRow of linked counterflow cooling tower cells sharing a common cold-water basin and rooftop walkway, each with its own fan stack. Multi-cell arrangements scale total heat-rejection capacity for large plants while keeping individual cells mo...
Configuration: Multi-cell, in-line row
عرض التفاصيلNight-time operational view of a multi-cell cooling tower bank, fan stacks floodlit with a visible water-vapor plume rising from each cell. Demonstrates the tower actively rejecting heat under full load at a commissioned site.
Cells: 5
عرض التفاصيلStacked bank of angled FRP chevron blades that captures and returns entrained water droplets from the exiting air stream before it leaves the cooling tower. Minimizes drift water loss to typically under 0.005% of circulating flow, cutting m...
Material: FRP (chevron blades)
عرض التفاصيلTan-colored wave-profile drift eliminator panel offering a lighter-weight, chemically resistant option for less demanding water chemistries. Removes fine water droplets from the discharge airstream while adding minimal pressure drop, an alt...
Material: PVC
عرض التفاصيلFRP composite torque tube with a precision steel mounting flange, transmitting rotational power from a right-angle gearbox to the fan hub in mechanical-draft cooling towers. Composite construction resists the humid, corrosive tower environm...
Material: FRP composite torque tube
عرض التفاصيلCross-fluted FRP film-fill pack that maximizes air-to-water contact surface area inside a counterflow cooling tower cell, improving evaporative heat-transfer efficiency. Suited to clean-to-moderate-fouling water in power, chemical, and refi...
Type: Cross-fluted film fill
عرض التفاصيلSplash-type trickle fill grid with triangular splash bars that break falling water into fine droplets to promote evaporation, tolerant of higher suspended-solids and scaling water than film fill. A common choice for field-erected towers han...
Type: Splash trickle grid
عرض التفاصيلFRP water-distribution nozzle with a wide-angle deflector cap that spreads incoming hot water evenly across the fill deck below, minimizing splash-back drift at the fill's leading edge. Threaded connection mounts directly into the tower's h...
Type: Water distribution nozzle
عرض التفاصيلLarge-diameter, high-volume axial fan with a bright metal hub cover, sized for underground rail-tunnel and metro-station ventilation duty. Provides smoke extraction, temperature control, and passenger-safety airflow in confined underground ...
Blades: ~11
عرض التفاصيلAngled axial exhaust fan with a distinctive rounded red hub cover, mounted at the base of a large cylindrical process duct or chimney. Used for boiler, kiln, or process-gas exhaust extraction where hot, particulate-laden air must be moved r...
Hub: Red hub cover
عرض التفاصيلMulti-blade exhaust fan with a smooth white conical hub, viewed head-on inside its round duct housing. A distinct design from the red-hub exhaust fan, illustrating Encon's range of duct-mounted extraction fans for general industrial ventila...
Blades: ~15
عرض التفاصيلCompact 6-blade axial fan intended to direct cooling air onto a cement rotary kiln's tyre (riding ring) and shell, helping control localized shell temperature and extend refractory and tyre life. Shown as a bench/demonstration unit ahead of...
Blades: 6
عرض التفاصيلCompact 7-blade FRP fan with a bolted metal hub, used in air washer and humidification systems to draw air through a water-spray or wetted-media bank for evaporative cooling and dust/odor control in textile mills and industrial halls.
Blades: 7
عرض التفاصيلLarger 12-blade fan installed in a wall opening ahead of a radiator/media bank, part of an air washer or humidification line. Moves conditioned air through wetted media to add humidity and cool process air in textile and industrial environm...
Blades: 12
عرض التفاصيلFRP axial fan with a red conical hub, installed through a circular wall opening to ventilate a textile mill floor. FRP construction resists the humid, lint-laden, corrosive atmosphere typical of spinning and weaving sheds while providing co...
Blades: 10
عرض التفاصيلPair of mesh-guarded axial fans with orange hubs mounted beneath a tea withering trough shed, blowing ambient or heated air up through the leaf bed. Reduces leaf moisture from 70-80% to around 50% during withering, the first stage of tea pr...
Units: Twin (2 fans)
عرض التفاصيلHigh-blade-count axial flow fan installed inside a large circular duct/shaft casing, backlit against open sky. Sized for underground mine and tunnel ventilation duty, supplying fresh air or exhausting foul air to meet mine-safety ventilatio...
Blades: ~16
عرض التفاصيلIn-progress fabrication shot showing individual fan blades being fitted to a blue FRP fan-casing shell on the shop floor. Illustrates the manufacturing and quality-assembly stage for large mine ventilation fan units before field shipment.
Material: FRP casing shell
عرض التفاصيلSingle elongated FRP fan blade for air-cooled condenser duty, molded from E-glass epoxy composite with an airfoil cross-section and a round root for bolting into a multi-piece hub clamp. Individually replaceable, so a damaged blade can be s...
Material: E-glass epoxy FRP
عرض التفاصيلCross-section cutaway of a deep-chord airfoil blade profile, showing the aerodynamic shape engineered to maximize air volume moved per unit of drive power. Represents Encon's higher-efficiency blade profile option for large-diameter ACC and...
Profile: Deep-chord airfoil
عرض التفاصيلCross-section cutaway of a slimmer airfoil profile, trading some air volume for reduced weight and drive load versus the deep-chord design. Offered as a lighter-duty blade profile option for smaller-diameter or lower-static-pressure fan app...
Profile: Slim airfoil
عرض التفاصيلGeneral-purpose paddle-style FRP fan blade with a straight taper and round mounting root, representative of Encon's standard replacement blade range for axial cooling and ventilation fans. Corrosion-resistant composite construction outlasts...
Material: FRP
عرض التفاصيلSmall, sharply twisted blade with a compact cylindrical mounting stub, distinct from the flat paddle-style blades used on large ACC fans. Its pronounced curvature suits smaller, higher-speed fan applications requiring more aggressive pitch ...
Profile: Twisted/curved
عرض التفاصيلFlat blade with a ribbed/embossed reinforcing surface pattern and a round mounting stub, a structurally reinforced alternative to smooth-surface blades. The rib pattern adds stiffness without adding significant weight, useful on wider-chord...
Profile: Flat, ribbed/embossed surface
عرض التفاصيلStudio product photo of a complete 6-blade FRP fan assembly with a chunky cast composite hub, ready for direct mounting to a motor shaft. Represents a standard mid-diameter fan unit sold as a complete, balanced, drop-in replacement assembly...
Blades: 6
عرض التفاصيل5-blade fan assembly shown with its two integrated motor/gearbox housings attached to the hub, illustrating a self-contained direct-drive fan package rather than a belt- or shaft-driven unit. Suited to compact package coolers where a separa...
Blades: 5
عرض التفاصيلComplete 6-blade FRP fan assembly finished in blue with a multi-bolt cast hub, a color/hub variant of Encon's standard fan-assembly line. Demonstrates the range of hub casting designs available across the same general blade configuration.
Blades: 6
عرض التفاصيل4-blade fan assembly built with a carbon-fiber-reinforced composite blade set on a heavy cast hub, offering a lighter, higher-stiffness alternative to standard E-glass FRP blades. Reduced blade mass lowers bearing and drive loads on high-sp...
Blades: 4
عرض التفاصيلCompact 8-blade FRP fan assembly with a small dark hub and asterisk-pattern blade layout, a smaller-diameter counterpart to Encon's larger ACC and cooling tower fan assemblies. Suited to smaller air-cooled heat exchanger cells or process ve...
Blades: 8
عرض التفاصيلSplit cast-metal clamp block that bolts around a blade's cylindrical root to lock it into the hub at a fixed pitch angle, shown across five sizes to match different blade-root diameters. Allows individual blade pitch adjustment and replacem...
Material: Cast metal
عرض التفاصيلComposite (FRP) equivalent of the cast-metal blade clamp, offered across a wider size range for larger or corrosion-sensitive installations. Two-piece design clamps around the blade root and bolts through the hub face; an assembled cube-sty...
Material: FRP composite
عرض التفاصيلTwin-disc flanged hub with a dense perimeter bolt pattern for mounting a full blade set plus a motor-side coupling flange. Its flat-disc design distributes blade loads evenly and suits fans requiring a rigid, low-runout mounting interface.
Type: Twin-disc, flanged
عرض التفاصيلCast hub with a dense radial bolt circle and a keyed center bore for direct shaft mounting, sized for a high blade count. Rugged cast construction handles the combined centrifugal and aerodynamic loading of large-diameter industrial axial f...
Type: Cast, radial bolt circle
عرض التفاصيلSix-position segmented clamp hub, each segment bolting independently around a blade root, allowing individual blade pitch setting on a 6-blade fan. Segmented design simplifies field blade replacement versus a one-piece cast hub.
Type: Segmented clamp (6 independent segments)
عرض التفاصيلMolded FRP fan stack (venturi-profile cylinder) that houses the fan and shapes airflow into the cooling tower or ACC cell, shown in both exterior and interior/bore views. Its curved waist profile reduces turbulence losses and improves fan e...
Material: Molded FRP
عرض التفاصيلMolded fiberglass grating panel used for walkways, platforms, and equipment decking around cooling towers and ACC structures. Open-mesh design provides slip resistance and drainage while resisting the corrosive, wet environment that would r...
Material: Fiberglass (pultruded/molded)
عرض التفاصيلPultruded fiberglass C-channel structural section, shown across multiple sizes, used as horizontal beams and girts in the load-bearing frame of field-erected FRP cooling towers. Corrosion-resistant alternative to galvanized steel channel fo...
Material: Pultruded fiberglass
عرض التفاصيلMolded FRP support grid/deck panel that carries fill media and distributes structural loads across a cooling tower cell's basin deck. Multi-cell ribbed construction combines light weight with high load-bearing stiffness for a corrosion-resi...
Material: Molded FRP
عرض التفاصيلPultruded fiberglass equal-angle section used for diagonal bracing, corner framing, and secondary support members in FRP cooling tower structures, shown across a range of leg sizes. Offers steel-comparable stiffness at a fraction of the wei...
Material: Pultruded fiberglass
عرض التفاصيلFlat pultruded/molded FRP plate stock used for gussets, mounting plates, and general fabrication within cooling tower and fan-casing assemblies. Supplied across a range of thicknesses for structural and non-structural applications requiring...
Material: Pultruded/molded FRP
عرض التفاصيلYellow pultruded FRP kick-plate section installed along walkway and platform edges around cooling towers to prevent tools and debris from falling and to protect panel edges from foot traffic. Bright color aids visibility as a safety-edge ma...
Material: Pultruded FRP
عرض التفاصيلSquare hollow pultruded FRP rung section used to build corrosion-resistant access ladders and stair treads on cooling tower and ACC platforms. Hollow profile keeps weight low while maintaining the stiffness needed for a safe foot-load rung.
Material: Pultruded FRP
عرض التفاصيلRound pultruded FRP tube with a serrated (ribbed) outer surface for improved grip, used as handrail or rung stock on tower access ladders and walkways. Corrosion resistance suits the constantly wet, evaporative environment around cooling to...
Material: Pultruded FRP
عرض التفاصيلSquare hollow pultruded FRP tube used as columns and diagonal struts in the structural frame of field-erected cooling towers, shown across multiple sizes and resin colors. Lightweight, corrosion-proof alternative to steel box section for we...
Material: Pultruded FRP
عرض التفاصيل
